Shop

Rubber Kennel Tile Canis LZ "Anthracite"

€13.00 / Piece
  • plus shipping costs

    /
  • Ready to ship

    from stock in 1-3 days
  • €52.00 / 4 Piece / m²
  • (5.60 kg /  Piece)

EAN: 4251469370647 | Item no.: 7064

The 3 cm thick Rubber Kennel Tile Canis Type LZ is made from rubber granules and has a hidden jigsaw interlock. Because the interlock sits below the surface, the joints form straight lines like those of a conventional tiled floor. The finely textured surface is very slip-resistant. The flooring is resilient, water-permeable and frost-resistant.

How do dogs move and rest on the tiles?

In a kennel fitted with Rubber Kennel Tile Canis, a dog may wait, doze in the sun or jump up when someone approaches the enclosure. The grippy surface gives paws and claws good purchase when the dog jumps up or turns, even when wet. The flooring gives slightly under each step and is kinder to paws. When the dog lies down, it is not lying on a cold floor because the tiles insulate against cold from the ground.

What is Rubber Kennel Tile Canis made from?

Rubber Kennel Tile Canis is made from ELT granules. These recycled tyre granules are bonded with polyurethane. The fine to medium granules create a finely textured surface that stands up to claws over time. The flooring does not rot or splinter. New tiles may smell of rubber at first. Outdoors, this smell fades after a short time.

How is Rubber Kennel Tile Canis laid?

The hidden jigsaw interlock of Rubber Kennel Tile Canis sits in a rebate along the underside of the tile edges. Two sides of every tile have the projecting tooth profile. The other two sides have the matching profile. This sets the laying direction. Each tile is placed from above until its rebate rests on that of the neighbouring tile and the teeth engage. The tiles can be laid in a regular grid or with staggered joints. In most cases, neither adhesive nor an edge restraint is needed. The base must remain load-bearing and stable, and it must be largely level. Concrete, paving and asphalt are suitable examples. On grass, soil or gravel, gravel grids filled with grit form the sub-base. Tiles at the edge are cut with a circular saw.

What happens to rain, urine and dirt?

Rain and urine pass through Rubber Kennel Tile Canis. On an impermeable base, water drains away along channels on the underside of the tiles. The area needs a gradient to prevent water from collecting. On gravel grids, water drains into the ground. A broom, garden hose or pressure washer is enough for cleaning. Areas where a dog regularly urinates should be rinsed more often with plenty of water to prevent odours from building up. The tiles can be disinfected when needed. The material is resistant to disinfectants.

Where can Rubber Kennel Tile Canis be used?

Rubber Kennel Tile Canis is suitable for garden kennels, units at boarding establishments and enclosures in animal shelters. It can be used in open and covered areas. The straight joints create a neat, even tiled surface that works well alongside nearby paving or a patio. If an area is altered, the tiles can be lifted and laid again elsewhere.

Selected variant 50 x 50 x 3 cm | 0,25 m²
Product type LZ (This product is made from cleaned black ELT granules with a fine grain size, bound with a polyurethane binder. ELT stands for "End of Life Tyres" and refers to rubber granules produced from recycled tyres. The fine grain creates a uniform, finely textured surface with a dense appearance that is comparatively easy to clean. Black and anthracite-coloured variants use a clear binder, while coloured versions achieve their appearance through a pigmented binder.)
Price and discount
0 m²

Product Highlights

Characteristics

UV-stabilised

ELT granules are UV-stabilised. Some coating shades may change slightly outdoors.

Harmful substance limits met

Meets EU limits for harmful substances. Initial rubber odour diminishes.

Indoor and outdoor use

Frost-resistant, suitable for indoor and outdoor use.

Efl

Normally flammable.

Product Details – Material and Structure

Comparative values

Are rubber tiles and rubber mats harmful to health?

Rubber tiles and rubber mats from WARCO are not harmful to health when used as intended. They are made from rubber granules bound with PU; the solvent-free PU binder cures fully during manufacture.

The rubber granules are predominantly recycled from end-of-life tyres (ELTs). The PAH content of ELT rubber granules may vary according to origin and batch; PAH means polycyclic aromatic hydrocarbons. Black ELT rubber granules contain carbon black, a fine industrial soot that gives the rubber its black colour. Surface abrasion may occur during use of rubber mats.

In two-layer versions, the wearing layer is made from newly manufactured EPDM, which is coloured throughout and free from harmful substances. The possible PAH variations associated with ELT rubber granules do not occur with EPDM. Versions with an EPDM wearing layer are particularly suitable for prolonged or intensive skin contact and for areas intended for babies. The relevant product description states whether a product has a two-layer construction.

Do WARCO rubber tiles contaminate soil or groundwater?

WARCO rubber tiles are made from rubber granules bound with polyurethane. Each granule is coated with polyurethane and held within the binder. The solvent-free binder cures fully during manufacture. Individual granules may remain attached to a tile after manufacture or come loose while the tiles are being laid. Any such manufacturing residue can be swept up or removed with a vacuum cleaner.

Vulcanised rubber and cured polyurethane are insoluble in water. Rainwater passing through the porous tiles does not dissolve these constituents. The same applies to individual granules left on the surface. On this basis, contamination of the soil or groundwater is not expected.

Are outdoor rubber tiles frost-resistant and suitable for use throughout the winter?

Outdoor rubber tiles made from polyurethane-bound rubber granules are frost-resistant and suitable for use throughout the winter. Their porous structure absorbs precipitation and allows it to pass downwards; water remaining in the pores has space to expand when it freezes, while the rubber granules and polyurethane binder remain elastic at sub-zero temperatures. The sub-base must also be constructed to withstand frost.

On bound sub-bases, water flows beneath and between the tiles in the direction of the fall towards the drainage system. On chippings or crushed stone, it drains vertically through the construction. If water collects beneath the tiles, a frost-susceptible sub-base may rise and then settle again after thawing. The tiles themselves remain unaffected, but the surface may become more uneven.

For winter maintenance, use a snow shovel with a smooth edge and avoid catching the tile edges. Salt used in normal quantities to melt ice does not harm the rubber granules.

How water-permeable are rubber tiles?

Rubber tiles can be water-permeable at rates ranging from nearly zero to more than 1,100 litres per square metre per hour. Water permeability depends on the particle-size fraction of the rubber granules used and on the pressing pressure applied during manufacture. The tiles are made from PU-bound rubber granules and have an open-pored structure.

Within this porous structure, water does not pass through the rubber itself but through the voids between the bonded granules. The more tightly the granules are compacted, the less water a rubber tile allows through. At low pressing pressure, the irregularly shaped granules sit loosely beside one another, leaving interconnected pores and fine channels through which water flows vertically downwards. An accredited institute measured more than 1,100 litres per square metre per hour in accordance with BS EN 12616, even after four weeks of weathering.

The respective water permeability value is stated as a comparative value in the product description. Rubber tiles made under high pressing pressure have an almost void-free granule structure and allow hardly any water through. A newly laid area absorbs water more slowly during its first days than the measured value may suggest, because the granule surfaces initially resist wetting, much like a new rain jacket. After several days of use, the floor covering reaches its full water permeability; scrubbing it with a little washing-up liquid speeds up this process.

The test report can be submitted to building authorities as evidence of water permeability. How an area is classified depends on the overall system build-up: precipitation can drain through the floor covering into the ground only if the sub-base beneath the rubber tiles also absorbs water.

Which laying patterns can be used for rubber tiles?

Rubber granules are used to make tiles. The main laying patterns are stack bond, diagonal bond, half bond (often called brick bond) and random bond. Which patterns are possible depends on the type of tile and its interlocking system.

In stack bond, the joints line up in both directions. Using tiles in different colours creates a chequerboard effect. Diagonal bond uses the same grid, but at an angle to the edges of the area. In half bond, each row is offset by half a tile length; in random bond, the offset changes from row to row.

Tiles without interlocks or connectors can generally be laid in any of these patterns. Tiles with push-fit connectors are usually designed for half bond, while tiles with an open or concealed jigsaw interlock are generally laid in stack or diagonal bond. Some ranges also allow tiles to be offset by half or a third of their length.

The specifications for the tile system always take precedence. A stable surface depends above all on tiles being properly connected, a suitable substrate and correct installation.

What should be considered before installing rubber tiles outdoors?

Installation of rubber tiles requires a load-bearing substrate designed to drain water. The tiles are water-permeable, so rainwater passing through them must infiltrate into the substrate or, alternatively, be discharged by a fall.

In central Europe, the suitable installation temperature is between 5 and 17 °C. Direct sunlight should be avoided, as it can cause tiles to heat up to differing degrees; throughout installation, all tiles should have an even temperature. Rain during installation does not harm the tiles, but soaked tiles must dry completely before installation.

General installation instructions must be followed, along with the requirements for the relevant product and installation system.

New rubber tiles may carry harmless release-agent residues from manufacture. Weathering washes these residues away; if required, they can be removed with water and a brush or with a pressure washer. The typical rubber smell of new tiles is harmless and reduces noticeably after a short time outdoors.

Can I lay rubber tiles on stone chippings or gravel?

For most rubber tiles to stay level on stone chippings or gravel in the long term, the loose material must first be stabilised with plastic honeycomb grids. These are sold under various names, including gravel grids, grass grids and honeycomb gravel grids. In each case, the cells hold the chippings in place and stop them shifting.

Chippings are generally of a similar size, with no fine material to fill the gaps between them. They cannot therefore be compacted effectively and remain prone to movement. Walk across chippings or gravel and you can feel them shift underfoot and hear them crunch. Beneath a rigid concrete slab, that movement hardly matters. Beneath a rubber tile 2 to 5 cm thick, however, hollows develop in the bed and show through on the tile surface.

First, remove the topsoil and level the ground to the required formation level. Spread a thin layer of chippings over the prepared ground and screed it carefully to a flat finish. Lay the gravel grids on top and fill the cells flush with their upper edges. Use crushed chippings rather than rounded gravel, as their angular particles interlock much better. Then lay the rubber tiles on this bed. Where the ground has poor load-bearing capacity, or where the build-up needs to withstand frost, install and compact a sub-base beneath the laying course of chippings.

Certain WARCO ranges with a flat underside are approved for installation directly on a bed of chippings, without a gravel grid. These ranges always require a sub-base of compacted crushed stone (MOT Type 1). Over this, spread a 2 to 3 cm laying course of crushed sand and chippings graded 0/5, then screed it level and compact it with a plate compactor. Unlike chippings alone, this mix contains fine sand, which allows it to firm up.

The laying course must remain within that thickness range. Below 2 cm, it cannot be screeded and compacted properly; above 3 cm, too much loose material remains beneath the patio tiles. After compaction, check the surface with a three-metre straightedge: the gap beneath it should be no more than 0.5 cm anywhere.

How do I install rubber flooring on concrete, asphalt or tiled floors?

Rubber flooring tiles can be installed directly over concrete, screed, asphalt or tiled floors as a loose-laid covering, without an additional sub-base.

With no additional sub-base required, the substrate must still be load-bearing, clean and sufficiently level. Remove loose material, oil and other contamination before laying. Larger irregularities, depressions and changes in level must be levelled out so that the tiles lie stably and do not create obtrusive edges.

The starting point and laying direction depend on the shape of the area and the required pattern. In many cases, starting in the centre helps to align the pattern evenly and produce similar cuts at opposite edges. For other areas, a straight boundary may provide the appropriate starting point.

Lay the tiles according to the chosen layout and join them firmly. Depending on the product, this is done using puzzle joints, dovetail joints or separate connectors. Measure the edge tiles, cut them to fit and then insert them.

Bonding is generally not required. Small cut pieces, stair treads and very small areas may require bonding.

How does the concealed jigsaw interlock on rubber tiles work?

With a concealed jigsaw interlock, the interlocking teeth are not located in the visible tile edge. They sit in a stepped rebate along the underside, which forms a step in the tile edge. Two adjacent sides carry the projecting profile, while the two opposite sides carry its counterpart.

During installation, each tile is placed from above so that its rebate rests on the counterpart of the neighbouring tile and the teeth engage. The overlapping rebates support the tile edges, while the interlocking teeth stop the tiles from separating within the laid surface. Where installation conditions are demanding, the tiles can be glued together at the teeth or within the rebate.

Only the narrow joint between the rounded tile edges is visible at the surface. Because the rebates overlap, the joint does not continue down to the sub-base. The surface beneath remains fully covered, so weeds cannot grow upwards from the sub-base through the joint.

Do algae or moss grow on products made of rubber granules?

Algae and moss do not generally establish themselves on products made from rubber granules. Rubber provides no nutrients and offers no basis for roots to take hold.

If sand, potting compost or other organic debris accumulates on the surface, growth may develop in these deposits. To prevent this, products made from rubber granules should be cleaned regularly, as should other floor coverings.

What is the best way to clean outdoor rubber tiles?

Outdoor rubber tiles should be cleared of leaves, soil and sand regularly.

Loose dirt can be swept away with a rubber broom or rinsed off with a hose. Rain also washes much of the dust and pollen away through water-permeable tiles.

Regular maintenance reduces the work required for more thorough cleaning.

For thorough outdoor cleaning, a pressure washer is suitable. The water jet loosens dirt from the textured surface and removes more persistent residues such as dog mess or food residue.

Where clean water is not sufficient, use either a neutral cleaner suitable for rubber or a mildly acidic cleaner. A specialist rubber cleaner is not required. Biodegradable Sonett WC Cleaner Mint is particularly suitable and has a pH value of around 5 to 6.

Apply the cleaner evenly, either neat or slightly diluted. After 10 to 15 minutes, work it in with a brush, then rinse the area thoroughly with clean water.

When brushing, use moderate pressure only. Excessive pressure can loosen granules from the bonded matrix.

Strongly alkaline cleaners, abrasive products and solvent-based cleaning products are unsuitable, as they can attack the surface of the rubber tiles.

Complementary products and recommended accessories

ALLESDICHT – Liquid Rubber Waterproofing ALLESDICHT – Liquid Rubber Waterproofing
AD

ALLESDICHT – Liquid Rubber Waterproofing

Black Grey

11 or 25 kg – liquid waterproofing by brush, trowel or spray – for balcony, terrace, flat roof, basement – tested as structural waterproofing, solvent-free

€118.90 / Piece €36.03 / m² x 2 mm

View product