Rubber Gym Mat RZ "Anthracite"
- /
-
Ready to ship
from stock in 1-3 days - €55.05 / 0.95 Piece / m²
- (25.50 kg / Piece)
EAN: 4251469363229 | Item no.: 6322
The Rubber Gym Mat type RZ consists of large-format mats. Their rounded jigsaw interlock joins them to form a continuous training surface. The mats are impact-absorbing and load-bearing. Cardio and strength equipment remains stable on them, while the floor underneath stays protected.
What is the Rubber Gym Mat used for?
The Rubber Gym Mat goes under cardio and strength equipment such as treadmills, cross trainers, exercise bikes, rowing machines, multi-gyms, racks and weight benches. In a home gym, it turns a basement or guest room into a proper training room. In a commercial gym, it covers entire equipment areas. The thickest version is recommended under heavy strength equipment. For greater impact absorption, place base layer tiles of a suitable density underneath.
How does the mat protect the floor?
The Rubber Gym Mat forms a protective layer between the equipment and the floor. It protects screed, tiles, parquet or laminate from scratches, dents and sweat. Even after many training sessions, weight benches and equipment feet leave hardly any marks on the mat.
What is the mat made from?
The Rubber Gym Mat is made from ELT granules. These are rubber granules from recycled end-of-life tyres that are bonded with polyurethane. The granules are fine and nearly uniform in size. This creates an even, closed and highly abrasion-resistant surface. New mats may have a rubber smell at first. With good ventilation, the smell fades after a while.
How do you lay the mats?
Each Rubber Gym Mat measures a little over one square metre. This makes it quick to cover a training room. The mats are pressed together from above. The rounded teeth of the jigsaw interlock hold them together without adhesive. Edging is not usually needed. The subfloor must be firm and largely level, such as screed, concrete, tiles, parquet or laminate. Cut the mat to size at the wall with a jigsaw or circular saw. If you move your home gym or refit a commercial gym, the mats can be lifted and relaid.
How do you keep the mats clean?
The Rubber Gym Mat absorbs very little liquid. Sweat stays on the surface and can be wiped away quickly after training. A vacuum cleaner, broom or damp mop is enough for day-to-day cleaning. The material is resistant to disinfectants. In a commercial gym, where many people train on the same equipment, the surface can therefore be disinfected regularly.
Discount
Product Highlights
Characteristics
Product Details – Material and Structure
Comparative values
Rubber mats made from PU-bound rubber granules can have a characteristic rubber smell, particularly when new. Whether and how strongly it is noticed depends on the material composition and on individual sensitivity to odours.
With WARCO rubber coverings, the inherent smell decreases over time. On well-ventilated outdoor areas such as balconies and terraces, it dissipates quickly. Heat may temporarily make the smell more noticeable.
The smell can remain noticeable for longer in indoor areas, conservatories and other poorly ventilated spaces where ventilation is limited. To reduce the initial inherent smell, rubber tiles may be stored for several days before installation in a dry, well-ventilated place. During storage, air should reach as many tile surfaces as possible.
After installation, regular brief periods of thorough ventilation or cross-ventilation support air exchange. With correct use, no adverse health effects from WARCO rubber coverings are known.
Rubber tiles and rubber mats from WARCO are not harmful to health when used as intended. They are made from rubber granules bound with PU; the solvent-free PU binder cures fully during manufacture.
The rubber granules are predominantly recycled from end-of-life tyres (ELTs). The PAH content of ELT rubber granules may vary according to origin and batch; PAH means polycyclic aromatic hydrocarbons. Black ELT rubber granules contain carbon black, a fine industrial soot that gives the rubber its black colour. Surface abrasion may occur during use of rubber mats.
In two-layer versions, the wearing layer is made from newly manufactured EPDM, which is coloured throughout and free from harmful substances. The possible PAH variations associated with ELT rubber granules do not occur with EPDM. Versions with an EPDM wearing layer are particularly suitable for prolonged or intensive skin contact and for areas intended for babies. The relevant product description states whether a product has a two-layer construction.
In normal use, furniture leaves no visible pressure marks or impressions on rubber tiles, provided the product description specifies that the covering is suitable for furniture and equipment. This includes patio tiles, balcony tiles, fitness tiles and floor coverings for trade fair and exhibition areas. Plant containers and training equipment may also stand on these surfaces.
The decisive factor is the point load, that is the weight in relation to the contact area of the furniture feet. Broad feet distribute the load, while very narrow feet concentrate the same weight over a small area. Patio and balcony tiles also accommodate the concentrated loading created by shoes with high heels. Tables and chairs of conventional design are therefore unlikely to leave marks. The limit is only approached by an exceptionally narrow metal foot carrying a high load.
Compressive strength is assessed under BS 7188. A force of 1000 newtons is applied to a test piece with a contact area of one square centimetre, equivalent to the weight of about 105 kilograms. Residual indentation is measured 24 hours after the load is removed. For patio and balcony tiles it is less than one millimetre. The corresponding rating appears in the technical data. The higher the rating, the smaller the residual indentation.
Impact-absorbing flooring made from PU-bound rubber granules reduces impact sound and the structure-borne sound it generates. The elastic floor covering absorbs impacts and reduces their transfer to the substrate.
Impact sound occurs when walking, jumping, moving furniture or setting down weights cause a floor or storey slab to vibrate. These vibrations travel through solid building components as structure-borne sound and can become audible as airborne sound in other rooms.
Structure-borne sound can also be caused by machinery and by installations fixed to the building. It may have causes and transmission paths other than impact sound, so it cannot be reduced by a floor covering alone.
Under load, a floor covering made from rubber granules deforms elastically. This deformation transfers the load to the substrate less abruptly, reduces the peak force and, through the covering’s internal damping, further weakens the remaining vibrations.
Sound-insulation tiles reduce excitation of the substrate from footsteps, jumps and impacting objects. Where higher requirements apply, multi-layer flooring systems with functional layers of differing elasticity can further reduce impact transmission. Their effectiveness depends on the properties of each layer, the load applied, and the existing floor or slab structure.
A suitable room for a home gym is dry, can be well ventilated, provides enough space for movement, has sufficient ceiling height and has a suspended floor or ground-bearing slab with adequate load-bearing capacity.
The space required depends on the intended training equipment and exercises. In addition to equipment footprints, adequate freedom of movement and safe clearances from walls, windows, radiators and other equipment should be allowed for.
Ceiling height must also accommodate overhead movements, pull-ups, skipping and jumps.
The suspended floor or ground-bearing slab must safely carry the static loads of training equipment, racks and weights, as well as the dynamic loads generated during training. Where heavy equipment or free weights are used, a structural engineer should check the load-bearing capacity if there is any doubt.
Effective ventilation allows heat, moisture and odours to escape. Particularly in rooms that are only lightly heated, the floor, walls and ceiling must remain permanently dry.
A basement can be used as a gym if it is dry and can be adequately ventilated.
Before conversion, damp patches, salt efflorescence, flaking plaster or mould should be investigated from a building physics perspective rather than relying on ventilation. Depending on the findings, the cause may be defective external waterproofing, a leaking pipe or condensation on cold surfaces. The measures required depend on those findings.
Drying through ventilation is only possible where the absolute humidity of the outdoor air is lower than that of the basement air. On warm, humid summer days, prolonged ventilation can increase moisture levels in the basement. Humidity-controlled ventilation or a dehumidifier can stabilise the indoor climate.
The required room height depends on the exercises and equipment planned. It must accommodate the height of the equipment, the maximum height reached during exercise and the necessary safety clearance to the ceiling. Equipment should be planned with the movement and safety areas specified by its manufacturer.
Before installing a rack, a heavy weight set or several strength machines, the basement floor should be checked for its capacity to carry the total load and the concentrated loads at machine feet or weight-storage racks.
Flooring should be selected for the actual level of use. Under cardio equipment, flooring made from 1 cm-thick gym mats is generally sufficient for vibration damping. Free-weight areas require thicker, shock-absorbing gym flooring: at least 2.5 cm, preferably 4 cm.
Where weights are dropped, the complete floor build-up must be designed to withstand the resulting impacts and vibration and to provide the necessary sound insulation.
The space needed for a home gym depends on training goals, equipment selection and the number of people intending to train at the same time.
A compact set-up with dumbbells, kettlebells, a weight bench and storage can often fit into around 10 m². With cardio equipment, up to 20 m² may be appropriate, while a rack and barbell may require up to 25 m².
Alongside the equipment, allow clear space for standing and mat exercises, as well as mobility work and stretching. Walkways should be at least 80 cm wide. Regularly used main routes can be up to 100 cm wide. Equipment with moving parts also requires the clearances specified by its manufacturer, with at least 200 cm generally required behind a treadmill.
These clearances should be planned on a level installation area so that all equipment feet rest evenly. Slip-resistant fitness flooring made from PU-bound rubber granules helps protect the substrate and reduces noise and vibration.
For cardio equipment, slabs from 1 cm thick are often sufficient. Thicker slabs are appropriate for floor exercises, free-weight areas, racks and heavy equipment. Both slab thickness and installation should follow the equipment manufacturer’s installation requirements so that the equipment stands level and stable.
A home gym needs a specialist gym floor covering designed for point loads and dynamic loads from training equipment, free weights, jumps and other movement-intensive exercises.
For these loads, a gym floor covering made from PU-bound rubber granules is slip-resistant, protects the substrate, absorbs part of the impact energy and reduces impacts and vibrations.
For effective basic cushioning, the gym floor covering should be at least 10 mm thick. The greater the equipment weight, impact load or potential drop height of weights, the higher-performing the gym floor covering must be. Damping cannot be determined from covering thickness alone: the relevant factors are the performance values of the specific gym floor covering, such as force reduction and impact sound reduction. Density and granule fraction are particularly significant for these performance values.
Where weights are dropped, the gym floor covering must be matched to their weight and drop height. Construction protection mats and comparable makeshift measures are not designed for use as gym floor coverings.
Slip-resistant fitness tiles made from PU-bound rubber granules can be used as flooring beneath gym equipment. The tiles attenuate impacts, reduce noise and structure-borne sound, and protect the floor from abrasion and pressure marks.
To protect the floor, the tiles must be installed on a firm, level substrate. All equipment feet must bear evenly and must not rest on a tile joint. Any unevenness must be levelled before installation.
For cardio equipment, fitness tiles with a thickness of about 1 cm or more are used. Heavy strength stations, racks and weight benches require thicker tiles.
For small or narrow equipment feet, an additional metal plate spreads the point load across a larger area.
For dropped weights, a simple equipment mat is not sufficient. The low-frequency vibrations created by dropped weights require a thicker or multi-layered flooring system for the training area.
The cost of setting up a home gym, also known as a home fitness room, ranges from around €500 to €15,000 (about £425 to £13,000), depending on the fitness equipment, room size and fit-out.
Fitness equipment is usually the main cost driver, while room size and the extent of the fit-out also affect the budget.
A basic set-up with dumbbells, a weight bench and a pull-up bar costs considerably less than a training area with a rack, cable machine or cardio equipment. Delivery and installation costs often need to be added.
Second-hand fitness equipment can reduce initial purchase costs, provided that its condition, operation and transport are checked before purchase.
The flooring must also be included in the calculation. Slip-resistant fitness flooring made from PU-bound rubber granules dampens noise and vibrations and protects the substrate.
Flooring costs depend on the size of the training area, the thickness of the tiles and the preparation of the substrate. With suitable tile systems, the area can be extended later.
Before fitting rubber flooring indoors, the tiles should be cleaned, dried completely and aired. The substrate must be level, load-bearing, clean and dry.
New tiles made from rubber granules may carry residues of manufacturing release agents and fine rubber dust. Before installation, it is advisable to clean the tiles outdoors with warm water; a mildly acidic cleaner suitable for rubber and a scrubbing brush can assist with cleaning. A pressure washer may be used from a sufficient distance. The tiles must then dry completely.
If cleaning before installation is not possible, the residues can be removed after fitting by repeatedly damp-mopping with warm water. New tiles have a characteristic odour which decreases over time; airing them outdoors for several days and regularly ventilating the room during the first few weeks will help it dissipate more quickly.
Before installation, the tiles should have reached room temperature. The installation instructions for the relevant product and installation system must be followed.
The appropriate cleaning method for rubber tiles within buildings depends on the area in which they are used and the surface texture.
In private homes, rubber brooms, vacuum cleaners or mops are usually sufficient for regular maintenance. A neutral cleaner suitable for rubber should be used. A mildly acidic cleaner may be used for mineral deposits.
Water-permeable rubber floor coverings must not be flooded where the substrate does not provide suitable drainage.
For larger or commercial areas, a scrubber dryer with a cylindrical brush is recommended. The brush type and contact pressure of the scrubber dryer must be matched to the floor covering.
Within buildings, a pressure washer is only suitable for stables or appropriately equipped halls where adequate drainage is available. It can also remove stubborn dirt from the textured tile surface.
Good design made easy.