ALLESDICHT – Waterproofing Coating AD "Black"
- /
-
Delivery in approx.
1-3 days - €38.56 / 1.11 Piece / m² x 2 mm
- (3.00 kg / Piece)
EAN: 4251469300354 | Item no.: 0035
ALLESDICHT – Waterproofing Coating is a ready-to-use liquid membrane for reliable moisture protection in both interior and exterior applications. Applied directly from the tub using a brush, roller, trowel or airless spray system, it cures to form a seamless and elastic barrier. It offers long-term protection against rising damp and water ingress – ideal for both refurbishment and new construction.
Applications and compatible substrates
Typical areas of use include flat roofs, balconies, terraces, basement walls, floor slabs, junctions and pipe penetrations – especially in locations exposed to moisture. ALLESDICHT adheres strongly to concrete, bitumen, brick, wood, metal, fibre cement, ceramic tiles and well-adhered existing coatings – even on slightly damp substrates.
Simple and safe application
The coating has a smooth, honey-like consistency and is applied in 2 to 3 coats. Each wet layer should not exceed 1.5 mm; the final dry membrane should be 2–3 mm thick. Average consumption is approx. 3.3 kg/m². The product is solvent-free, water-dilutable, pH-neutral and non-irritant – suitable even for confined spaces. Application is recommended at ambient temperatures between +5 °C and +30 °C. In critical areas, a reinforcement mesh can be embedded between layers.
Certified quality and fire classification
ALLESDICHT is certified to DIN 18533 for use in structural waterproofing and meets fire classification B2 according to DIN 4102-1. It is suitable for contact with standing or pressurised water. Available in black, grey or red, in tubs of 3 kg, 11 kg or 25 kg.
Discount
Product Highlights
Characteristics
Product Details – Material and Structure
Comparative values
To calculate how many tiles you need for your project, simply use the online installation planner available in the shop. This free browser-based tool is directly accessible on each product page – just below the price and quantity selection. Click on “Plan installation” to open the tool instantly – no registration or download required.
Enter the dimensions of your area, such as the length and width in metres. The planner will then automatically calculate the total number of tiles required, including a realistic allowance for offcuts. You’ll also be shown a suitable layout pattern for the selected product. The tool is user-friendly, accurate and ideal for planning your material requirements with confidence.
Patio waterproofing protects the structure underneath from water ingress. The waterproofing sits on the structural layer – beneath your floor finish – and you must have adequate fall for water to drain away.
Apply ALLESDICHT as a liquid coating directly onto the prepared substrate. Concrete, screed, old tile or bitumen all work well. The advantage on a patio is that the seamless coating seals tightly where the house wall meets the slab, at door thresholds and around drains – exactly the weak points where sheet systems often fail. Apply two or three coats to achieve a minimum dry thickness of 2 mm. The coating’s flexibility bridges small cracks in the substrate beneath.
Once it’s fully cured, you can lay your chosen floor finish straight on top – rubber tiles, ceramic tiles or a further coating.
ALLESDICHT is ready to apply straight from the tin. Give it a thorough stir before you start. Depending on the area and how accessible it is, you can brush it on, spray it with an airless sprayer, apply it with a trowel or use a soft broom. It bonds reliably to nearly all standard building substrates: concrete, timber, bitumen, tiles and metal.
Your substrate must be clean, dry and completely free of dust, oil and grease. If the surface is very absorbent, treat it with a primer coat beforehand.
Apply ALLESDICHT in two or three coats, with each coat drying before the next one goes down. Keep each coat to a maximum of 1.5 mm when wet. Once fully cured, the total thickness should be at least 2–3 mm. Where you have junctions, penetrations or areas under stress, embed a reinforcing fabric to stabilise the joint further. The finished coating is elastic and fully waterproof, with an elongation of over 200 %, so it moves with the substrate as it shifts and settles without tearing.
The cured coating must be at least 2–3 mm thick to give proper protection. The material shrinks during drying – roughly one-third of the thickness disappears. A wet coat of 1.5 mm becomes about 1 mm when it’s fully cured. This means you’ll need 3.0 to 4.5 mm of wet material in total.
Apply ALLESDICHT in two, three or more passes to reach this target. Each pass must be no more than 1.5 mm wet thickness and must dry completely before you add the next one. How many passes you actually need depends on the structural requirements, what the substrate is like and the conditions on the day. At critical points – junctions, penetrations and corners – an additional coat often pays for itself.